config.h

Go to the documentation of this file.

/*This file is prepared for Doxygen automatic documentation generation.*/

/* Copyright (c) 2009 Atmel Corporation. All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 * this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 * this list of conditions and the following disclaimer in the documentation
 * and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 * from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an Atmel
 * AVR product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE EXPRESSLY AND
 * SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT,
 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
 * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#ifndef _CONFIG_H_
#define _CONFIG_H_

// Compiler switch (do not change these settings)
#include "lib_mcu/compiler.h"             // Compiler definitions
#ifdef __GNUC__
   #include <avr/io.h>                    // Use AVR-GCC library
#elif __ICCAVR__
   #define ENABLE_BIT_DEFINITIONS
   #include <ioavr.h>                     // Use IAR-AVR library
#else
   #error Current COMPILER not supported
#endif



#include "conf/conf_scheduler.h"          // Scheduler tasks declaration

#define USE_ADC

#define  STK525   1                       // do not change these settings
#define  TARGET_BOARD STK525
#include "lib_board\stk_525\stk_525.h"

#define FOSC 8000

#define USE_TIMER16 TIMER16_1

// -------- END Generic Configuration -------------------------------------

#define HID_GENERIC_DEMO_FULL   DISABLE         

#define HOST_SYNC_MODE  ENABLE

// UART Sample configuration, if we have one ... __________________________
#define BAUDRATE        57600
#define USE_UART2
#define UART_U2

#ifndef __GNUC__
#define uart_putchar putchar
#endif

#define r_uart_ptchar int
#define p_uart_ptchar int


// ADC Sample configuration, if we have one ... ___________________________

#define ADC_PRESCALER 32
#define ADC_RIGHT_ADJUST_RESULT 1
#define ADC_INTERNAL_VREF  2

#define SBC_VENDOR_ID         {'A','T','M','E','L',' ',' ',' '}      // 8 Bytes only
#define SBC_PRODUCT_ID        {'A','T','9','0','U','S','B','1','2','8',' ','M',' ','S',' ',' '}  // 16 Bytes only
#define SBC_REVISION_ID       {'0','.','0','0'}  // 4 Bytes only

#define NB_IDLE_POLLING_SOF  2               
#define MOUSE_SPEED          3               

// Nav_util.c configuration
#define MAX_FILE_LENGHT       30

// USHELL configuration, if we have one ... ___________________________

#define USHELL_DFU            ENABLE
#define USHELL_USB            ENABLE
#define USHELL_HID            ENABLE
#define USHELL_HISTORY        5
#define USHELL_SIZE_CMD_LINE  30
#define USHELL_NB_LINE        20
#define USHELL_SIZE_OF_EXT_BUFFER_TO_PERF_CMD 4

#define TRACE                 DISABLE

#if (TRACE==ENABLE)
extern void ushell_trace_msg(U8 code *str);
#define LOG_STR_CODE(s)    ushell_trace_msg(s)
#endif




#endif // _CONFIG_H_

---